Hit enter to search or ESC to close
THE BUYER'S GUIDE / SELECTION
A buyer-focused guide to checking whether the GI Angle Furring System from Wen 'an Jinkai Building Materials Co., Ltd. fits a suspended gypsum board ceiling project. It covers the published profile size, thickness range, length, material, finish type and regional system, plus the points buyers should confirm in writing before ordering.

Application fit: suspended ceiling framing for gypsum boards with a concealed grid and smooth finish
Profile size: 25.4 x 25.4 mm, checked against the ceiling design and accessories
Thickness: 0.30 mm – 0.60 mm, selected by the project engineer's load and spacing requirements
Length: 3.0 m standard; custom lengths available upon request
Material: galvanized steel (GI); confirm coating details for humid or coastal sites
Regional system: designed for the South American system; confirm suitability for other markets and codes
A GI Angle Furring System is a suspended steel frame that sits above the ceiling. Gypsum boards are fixed to it, and the frame stays hidden once the ceiling is finished. Before you compare quotations, check whether the published specification matches your ceiling design, board type and project standards. This guide uses only the product information published by Wen 'an Jinkai Building Materials Co., Ltd. It points out where buyers need written confirmation and does not assume anything that has not been published.
The published product description says the system is suspended ceiling framing for gypsum boards. It uses a concealed grid, so the ceiling surface is smooth and plain and can be painted or wallpapered. That makes it relevant to residential, office and retail interiors where the frame should not show.
Where it may not apply: if your design calls for an exposed T-grid with lay-in tiles, a concealed furring frame is a different kind of system. Pick the ceiling type first, then the frame.
| Item | Published specification |
|---|---|
| Product | GI Angle / Furring System |
| Application | Suspended ceiling framing |
| Profile size | 25.4 x 25.4 mm |
| Available thickness | 0.30 mm – 0.60 mm |
| Standard length | 3.0 m |
| Custom lengths | Available upon request |
| Material | Galvanized steel (GI) |
| Finish type | Smooth / concealed grid |
| Compatibility | Gypsum boards |
| Regional standard | South American system |
Things to compare against your drawings:
The product page describes this GI Angle Furring System as built for the South American construction market and the South American system. If your project is in another region, for example the United States, Europe, the Middle East or Southeast Asia, ask whether the profile and accessories fit the framing method and building codes used there.
The page also mentions following ASTM and regional South American quality standards. This guide does not treat that as a certification. If your specification needs a particular standard, test report or certificate, ask for the documents and check them before you place an order.
The supplier says the galvanized steel resists rust and oxidation, including in humid tropical climates. For humid or coastal sites, ask for the galvanizing details and any supporting test data. The published material does not give a coating weight, so that figure has to be confirmed separately.
The product information describes modular assembly for efficient installation. It also says technical guidance on installation and load-bearing calculations is available to architects and engineers. Treat this as a starting point. Suspension spacing, hanger layout and load checks should still be approved by your project engineer under local rules.
The published material does not set prices, lead times, minimum order quantities or certifications. Agree on these in writing:
The GI Angle Furring System is likely a good fit if you need a concealed, galvanized steel frame for smooth gypsum board ceilings and your design works with a 25.4 x 25.4 mm profile in the 0.30–0.60 mm thickness range. If your project follows a non-South American framing system or needs specific certificates, confirm those points with the supplier first. You can review the full product page for the GI Angle Furring System and send your drawings and requirements for review.
THE PEOPLE
About the author
Robert Miller
He joined Jinkai five years ago, quickly establishing key partnerships with distributors across the USA and Canada. Robert is passionate about delivering high-quality, cost-effective ceiling solutions and is a strong advocate for our automated production processes, consistently highlighting their impact on product consistency and durability. He regularly contributes to industry publications, offering insights on trends in steel framing and T-grid systems.
THE COMPANY
Wen'an Jinkai Building Materials Co., Ltd. is located in Dongdu Industrial Park, State-owned Huangpu Farm, Wen'an County, Langfang City, Hebei Province. Bordering Xiongan New Area to the east and Tianjin Port to the west, it enjoys easy access to transport networks, with the Beijing–Taipei Expressway to its east, and the Daqing–Guangzhou Expressway as well as Beijing–Dezhou Expressway to its west.
Founded in 2008, the company is now a key foreign trade enterprise in Wen'an County.…
YOUR NEXT STEP
Use case, specification, quantity and delivery window: make the next conversation specific.
Nov 10, 26
Technical Factors Affecting 1 5 8 metal stud price and Quality
Nov 09, 26
High Quality 1 5 8 metal stud price for Commercial Framing
Nov 09, 26
Heavy Duty Stainless Steel Press Studs or B8M Weld Studs: Which Fastener Fits?
If you are interested in our products, you can choose to leave your information here, and we will be in touch with you shortly.
